The Gluster Blog

Gluster blog stories provide high-level spotlights on our users all over the world

Setting up a test-environment for Apache CloudStack and Gluster

Gluster
2014-02-23

This is an example of how to configure an environment where you can test CloudStack and Gluster. It uses two machines on the same LAN, one acts as a KVM hypervisor and the other as storage and management server. Because the (virtual) networking in the hypervisor is a little more complex than the networking on the management server, the hypervisor will be setup with an OpenVPN connection so that the local LAN is not affected with ‘foreign’ network traffic.

I am not a CloudStack specialist, so this configuration may not be optimal for real world usage. It is the intention to be able to test CloudStack and its Gluster integration in existing networks. The CloudStack installation and configuration done is suitable for testing and development systems, for production environments it is highly recommended to follow the CloudStack documentation instead.

 .----------------.                       .-------------------.
 |                |                       |                   |
 | KVM Hypervisor | <------- LAN -------> | Management Server |
 |                |    ^-- OpenVPN --^    |                   |
 '----------------'                       '-------------------'
agent.cloudstack.tld                      storage.cloudstack.tld

Both systems have one network interface with a static IP-address. In the LAN, other IP-addresses can not be used. This makes it difficult to access virtual machines, but that does not matter too much for this testing.

Both systems need a basic installation:

  • Red Hat Enterprise Linux 6.5 (CentOS 6.5 should work too)
  • Fedora EPEL enabled (howto install epel-release)
  • enable ssh access
  • SELinux in permissive mode (or disabled)
  • firewall enabled, but not restricting anything
  • Java 1.7 from the standard java-1.7.0-openjdk packages (not Java 1.6)

On the hypervisor, an additional (internal only) bridge needs to be setup. This bridge will be used for providing IP-addresses to the virtual machines. Each virtual machine seems to need at least 3 IP-addresses. This is a default in CloudStack. This example uses virtual networks 192.168.N.0/24, where N is 0 to 4.

Configuration for the main cloudbr0 device:

#file: /etc/sysconfig/network-scripts/ifcfg-cloudbr0
DEVICE=cloudbr0
TYPE=Bridge
ONBOOT=yes
BOOTPROTO=static
IPADDR=192.168.0.1
NETMASK=255.255.255.0
NM_CONTROLLED=no

And the additional IP-addresses on the cloudbr0 bridge (create 4 files, replace N by 1, 2, 3 and 4):

#file: /etc/sysconfig/network-scripts/ifcfg-cloudbr0:N
DEVICE=cloudbr0:N
ONBOOT=yes
BOOTPROTO=static
IPADDR=192.168.N.1
NETMASK=255.255.255.0
NM_CONTROLLED=no

Enable the new cloudbr0 bridge with all its IP-addresses:

# ifup cloudbr0

Any of the VMs that have a 192.168.*.* address, should be able to get to the real LAN, and ultimately also the internet. Enabling NAT for the internal virtual networks is the easiest:

# iptables -t nat -A POSTROUTING -o eth0 -s 192.168.0.0/24 -j MASQUERADE
# iptables -t nat -A POSTROUTING -o eth0 -s 192.168.1.0/24 -j MASQUERADE
# iptables -t nat -A POSTROUTING -o eth0 -s 192.168.2.0/24 -j MASQUERADE
# iptables -t nat -A POSTROUTING -o eth0 -s 192.168.3.0/24 -j MASQUERADE
# iptables -t nat -A POSTROUTING -o eth0 -s 192.168.4.0/24 -j MASQUERADE
# service iptables save

The hypervisor will need to be setup to act as a gateway to the virtual machines on the cloudbr0 bridge. In order to so do, a very basic OpenVPN service does the trick:

# yum install openvpn
# openvpn --genkey --secret /etc/openvpn/static.key
# cat << EOF > /etc/openvpn/server.conf
dev tun
ifconfig 192.168.200.1 192.168.200.2
secret static.key
EOF
# chkconfig openvpn on
# service openvpn start

On the management server, it is needed to configure OpenVPN as a client, so that routing to the virtual networks is possible:

# yum install openvpn
# cat << EOF > /etc/openvpn/client.conf
remote real-hostname-of-hypervisor.example.net
dev tun
ifconfig 192.168.200.2 192.168.200.1
secret static.key
EOF
# scp real-hostname-of-hypervisor.example.net:/etc/openvpn/static.key /etc/openvpn
# chkconfig opennvpn on
# service openvpn start

In /etc/hosts (on both the hypervisor and management server) the internal hostnames for the environment should be added:

#file: /etc/hosts
192.168.200.1 agent.cloudstack.tld
192.168.200.2 storage.cloudstack.tld

The hypervisor will also function as a DNS-server for the virtual machines. The easiest is to use dnsmasq which uses /etc/hosts and /etc/resolv.conf for resolving:

# yum install dnsmasq
# chkconfig dnsmasq on
# service dnsmasq start

The management server is also used as a Gluster Storage Server. Therefor it needs to have some Gluster packages:

# wget -O /etc/yum.repo.d/glusterfs-epel.repo \
http://download.gluster.org/pub/gluster/glusterfs/3.4/LATEST/RHEL/glusterfs-epel.repo
# yum install glusterfs-server
# vim /etc/glusterfs/glusterd.vol
<add "option rpc-auth-allow-insecure on" to the managent volume>
# service glusterd restart

Create two volumes where CloudStack will store disk images. Before starting the volumes, apply the required settings too. Note that the hostname that holds the bricks should be resolvable by the hypervisor and the Secondary Storage VMs. This example does not show how to create volumes for production usage, do not create volumes like this for anything else than testing and scratch data.

# mkdir -p /bricks/primary/data
# mkdir -p /bricks/secondary/data
# gluster volume create primary storage.cloudstack.tld:/bricks/primary/data
# gluster volume set primary storage.owner-uid 36
# gluster volume set primary storage.owner-gid 36
# gluster volume set primary server.allow-insecure on
# gluster volume set primary nfs.disable true
# gluster volume start primary
# gluster volume create secondary storage.cloudstack.tld:/bricks/secondary/data
# gluster volume set secondary storage.owner-uid 36
# gluster volume set secondary storage.owner-gid 36
# gluster volume start secondary

When the preparation is all done, it is time to install Apache CloudStack. It is planned to have support for Gluster in CloudStack 4.4. At the moment not all required changes are included in the CloudStack git repository. Therefor, is is needed to build the RPM packages from the Gluster Forge repository where the development is happening. On a system running RHEL-6.5, checkout the sources and build the packages (this needs a standard CloudStack development environment, including java-1.7.0-openjdk-devel, Apache Maven and others):

$ git clone git://forge.gluster.org/cloudstack-gluster/cloudstack.git
$ cd cloudstack
$ git checkout -t -b wip/master/gluster
$ cd packaging/centos63
$ ./package.sh

In the end, these packages should have been build:

  • cloudstack-management-4.4.0-SNAPSHOT.el6.x86_64.rpm
  • cloudstack-common-4.4.0-SNAPSHOT.el6.x86_64.rpm
  • cloudstack-agent-4.4.0-SNAPSHOT.el6.x86_64.rpm
  • cloudstack-usage-4.4.0-SNAPSHOT.el6.x86_64.rpm
  • cloudstack-cli-4.4.0-SNAPSHOT.el6.x86_64.rpm
  • cloudstack-awsapi-4.4.0-SNAPSHOT.el6.x86_64.rpm

On the management server, install the following packages:

# yum localinstall cloudstack-management-4.4.0-SNAPSHOT.el6.x86_64.rpm \
cloudstack-common-4.4.0-SNAPSHOT.el6.x86_64.rpm \
cloudstack-awsapi-4.4.0-SNAPSHOT.el6.x86_64.rpm

Install and configure the database:

# yum install mysql-server
# chkconfig mysqld on
# service mysqld start
# vim /etc/cloudstack/management/classpath.conf

# cloudstack-setup-databases cloud:secret --deploy-as=root:

Install the systemvm templates:

# mount -t nfs storage.cloudstack.tld:/secondary /mnt
# /usr/share/cloudstack-common/scripts/storage/secondary/cloud-install-sys-tmplt \
-m /mnt \
-h kvm \
-u http://jenkins.buildacloud.org/view/master/job/build-systemvm-master/lastSuccessfulBuild/artifact/tools/appliance/dist/systemvmtemplate-master-kvm.qcow2.bz2
# umount /mnt

The management server is now prepared, and the webui can get configured:

# cloudstack-setup-management

On the hypervisor, install the following additional packages:

# yum install qemu-kvm libvirt glusterfs-fuse
# yum localinstall cloudstack-common-4.4.0-SNAPSHOT.el6.x86_64.rpm \
cloudstack-agent-4.4.0-SNAPSHOT.el6.x86_64.rpm
# cloudstack-setup-agent

Make sure that in /etc/cloudstack/agent/agent.properties the right NICs are being used:

guest.network.device=cloudbr0
private.bridge.name=cloudbr0
private.network.device=cloudbr0
network.direct.device=cloudbr0
public.network.device=cloudbr0

Go to the CloudStack webinterface, this should be running on the management server: http://real-hostname-of-mgmt.example.net:8080/client The default username/password is: admin / password

It is easiest to skip the configuration wizard (not sure if that supports Gluster already). When the normal interface is shown, under ‘Infrastructure’ a new ‘Zone’ can get added. The Zone wizard will need the following input:

  • DNS 1: 192.168.0.1
  • Internal DNS 1: 192.168.0.1
  • Hypervisor: KVM

Under POD, use these options:

  • Reserved system gateway: 192.168.0.1
  • Reserved system netmask: 255.255.255.0
  • Start reserved system IP: 192.168.0.10
  • End reserved system IP: 192.168.0.250

Next the network config for the virtual machines:

  • Guest gateway: 192.168.1.1
  • Guest system netmask: 255.255.255.0
  • Guest start IP: 192.168.1.10
  • Guest end IP: 192.168.1.250

Primary storage:

  • Type: Gluster
  • Server: storage.cloudstack.tld
  • Volume: primary

Secondary Storage:

  • Type: nfs
  • Server: storage.cloudstack.tld
  • path: /secondary

Hypervisor agent:

  • hostname: agent.cloudstack.tld
  • username: root
  • password: password

If this all succeeded, the newly created Zone can get enabled. After a while, there should be two system VMs listed in the Infrastructure. It is possible to log in on these system VMs and check if all is working. To do so, log in over SSH on the hypervisor and connect to the VMs through libvirt:

# virsh list
 Id    Name                           State
----------------------------------------------------
 1     s-1-VM                         running
 2     v-2-VM                         running

# virsh console 1
Connected to domain s-1-VM
Escape character is ^]

Debian GNU/Linux 7 s-1-VM ttyS0

s-1-VM login: root
Password: password

root@s-1-VM:~#

Log out from the shell, and press CTRL+] to disconnect from the console.

To verify that this VM indeed runs with the QEMU+libgfapi integration, check the log file that libvirt writes and confirm that there is a -drive with a glusterfs+tcp:// URL in /var/log/libvirt/qemu/s-1-VM.log:

... /usr/libexec/qemu-kvm -name s-1-VM ... -drive file=gluster+tcp://storage.cloudstack.tld:24007/primary/d691ac19-4ec1-47c1-b765-55f804b78bec,...

BLOG

  • 06 Dec 2020
    Looking back at 2020 – with g...

    2020 has not been a year we would have been able to predict. With a worldwide pandemic and lives thrown out of gear, as we head into 2021, we are thankful that our community and project continued to receive new developers, users and make small gains. For that and a...

    Read more
  • 27 Apr 2020
    Update from the team

    It has been a while since we provided an update to the Gluster community. Across the world various nations, states and localities have put together sets of guidelines around shelter-in-place and quarantine. We request our community members to stay safe, to care for their loved ones, to continue to be...

    Read more
  • 03 Feb 2020
    Building a longer term focus for Gl...

    The initial rounds of conversation around the planning of content for release 8 has helped the project identify one key thing – the need to stagger out features and enhancements over multiple releases. Thus, while release 8 is unlikely to be feature heavy as previous releases, it will be the...

    Read more